Search Results

The engine-out emissions and fuel consumption rates for a modern, heavy-duty diesel engine were compared when fueling with a conventional diesel fuel and three water-blend-fuel emulsions. Four different fuels were studied: (1) a conventional diesel fuel, (2) PuriNOx,™ a water-fuel emulsion using the same conventional diesel fuel, but having 20% water by mass, and (3,4) two other formulations of the PuriNOx™ fuel that contained proprietary chemical additives intended to improve combustion efficiency and emissions characteristics. The emissions data were acquired with three different injection-timing strategies using the AVL 8-Mode steady-state test method in a Caterpillar 3176 engine, which had a calibration that met the 1998 nitrogen oxides (NOX) emissions standard.

Forthcoming on-highway 2005/2007 European and North American emission regulations will require modern diesel engines to be equipped with Diesel Particulate Filters (DPF) capable of trapping up to 99% of the exhaust particulate matter. Since diesel particulates (soot) accumulate in the filter over time, the overall system needs to be regenerated by attaining the ignition temperature of soot, which in the presence of oxygen is >600 °C. Catalyzed DPFs regenerate at temperatures as low as ∼300 °C. One of the major issues facing OEMs, aftertreatment system manufacturers, and lubricant formulators is the potential effects of the lubricant-derived ash deposits and their impact on a pressure increase across filters, as well as overall filter performance and its service characteristics.

Over the past decade, laser diagnostics have improved our understanding of many aspects of diesel combustion. However, interactions between the combusting fuel jet and the piston-bowl wall are not well understood. In heavy-duty diesel engines, with typical fuels, these interactions occur with the combusting vapor-phase region of the jet, which consists of a central region containing soot and other products of rich-premixed combustion, surrounded by a diffusion flame. Since previous work has shown that the OH radical is a good marker of the diffusion flame, planar laser-induced fluorescence (PLIF) imaging of OH was applied to an investigation of the diffusion flame during wall interaction. In addition, simultaneous OH PLIF and planar laser-induced incandescence (PLII) soot imaging was applied to investigate the likelihood for soot deposition on the bowl wall.

Motorcycle OEMs faced with stringent global fuel economy and emission regulations are being forced to develop new hardware and emissions control technologies to remain compliant. Motorcycle oils have become an enabling technology for the development of smaller, more efficient engines operating at higher power density. Many OEMs have therefore become reliant on lubricants to not only provide enhanced durability under more extreme operating conditions, but to also provide fuel economy benefits through reduced energy losses. Unlike passenger car oils that only lubricate the engine, motorcycle oils must lubricate both the engine and the drive train. These additional requirements place different performance demands versus a crankcase lubricant. The drive train includes highly loaded gears that are exposed to high pressures, in turn requiring higher levels of oil film strength and antiwear system durability.

Multifunctional or universal lubricating oils which service both gasoline and diesel engines have gained widespread commercial acceptance. Since 1970, numerous changes and additions have altered the performance tests and specifications which define the quality of these lubricants. New parameters include single cylinder and multicylinder diesel engine testing, valve train wear protection, clutch plate friction retention, extended drain interval and lubricant related fuel economy. In response to these requirements, new additive systems were developed. This paper discusses observed base oil-additive-engine test interactions and compares the performance of one of these additive systems to that of the old.

A new generation of fluid technology using novel diesel fuel detergent/dispersant chemistry provides a multitude of beneficial effects to the diesel engine, especially the latest model designs. In addition to improved injector, valve and combustion chamber deposit removal, the additive restores power, fuel economy, performance and emission levels1. Positive observations have also been documented along with improved performance concerning crankcase lube viscosity, soot loading and TBN retention. An even greater added benefit is the inherent capability of the fuel additive to deal with several EGR issues now prominent with the introduction of new engines. Recent research, reported herein, has uncovered the extensive efficacy of this chemistry for piston durability and neutralization of ring corrosion phenomena. All of the beneficial additive attributes are further enhanced with increased oxidative and thermal fuel stability and no loss of filterability.

The next generation of engine oil under development has been formulated to maintain beneficial oil lubrication properties at increased engine operating temperatures, increased drain-oil intervals, and with the recirculation of exhaust gas back through the engine (EGR). These conditions result in the formation of degradation products from decomposed fuel, additives, and base oil. Decomposition products containing reactive sulfur can result in the corrosion of copper alloys. Sulfur-containing compounds currently used in these formulations can include zinc dithiophosphates (ZDP), molydithiophosphates, molydithiocarbamates, and molybdic acid/amine complexes, along with sulfur containing detergents and antioxidants. Interactions among these components and others in the formulation often determine the propensity of these formulations for corrosion. This paper will discuss the results of corrosion bench tests used to screen oil formulations for copper corrosion.

The two-color method for measuring temperature and optical thickness of soot (KL) has become a standard diagnostic tool for the evaluation of engine designs and technologies relative to soot formation and flame temperature. Implementation of the two-color technique typically requires two cameras or a set of half-pass mirrors and optical narrow band-pass filters. In this paper, a technique for collecting and interpreting two-color images with a single calibrated camera without image splitting and filtering hardware is demonstrated and discussed. This method uses a relatively inexpensive commercial, 10-bit, RGB color, CCD camera capable of 16 μs exposure times. The CCD has published spectral response curves in the visible range, but a method for obtaining the spectral response for the optical system using a monochromator is discussed.

All automotive gear oils must satisfy a series of standard industry or Original Equipment Manufacturer (OEM) tests. These usually include bench, axle dynamometer, and field tests. However, product development testing must extend beyond satisfying standard test protocols. This is especially true as increased emphasis is placed on extending oil drain intervals and increasing equipment life in the face of greater performance demands through new heavy-duty vehicle designs. End-users ultimately benefit from extended oil drain intervals and increased equipment life. However, the effort to achieve both initiatives will prove successful only through careful development and selection of the proper performance additives and base fluids. Also, a broad focus must be maintained to satisfy all lubricant requirements. These requirements build on a solid base of standard features and include new features that stretch the current envelope of gear oil performance.

With the increasing use of modern, EGR-equipped, heavy-duty diesel engines and the use of lower sulfur and alternate fuels, such as biodiesel, lubricants are being exposed to a range of different compositions of acids. To complement the traditional detergent bases, todays lubricants have evolved to include a higher proportion of basic materials from amine-derived sources to aid in oxidation and soot control. This paper explores the impact of the different sources of acids, some of the issues they create and how they can be addressed, exemplified in a prototype CJ-4 lubricant formulation.

With the developments of Industry 4.0, data analytics solutions and their applications have become more prevalent in the manufacturing industry. Currently, the typical software architecture supporting these solutions is modular, using separate software for data collection, storage, analytics, and visualization. The integration and maintenance of such a solution requires the expertise of an information technology team, making implementation more challenging for small manufacturing enterprises. To allow small manufacturing enterprises to feasibly obtain the benefits of Industry 4.0 data analytics, a full-stack data analytics framework is presented, and its performance evaluated as applied in the common industrial analytics scenario of predictive maintenance. The predictive maintenance approach was achieved by using a full-stack data analytics framework comprised of the PTC Inc. Thingworx software suite.

A zero-dimensional model is introduced that combines recently presented empirical relationships for diesel jet penetration and flame lift-off length in order to produce a realistic heat release rate and predict the temperature and equilibrium species concentrations in five zones within the combustion chamber. The new model describes the compression, combustion and expansion portions of a diesel cycle. During fuel injection and combustion, the temperature, geometry, and composition of five zones are calculated: 1) vaporizing fuel and air, 2) vaporized reactants, 3) premixed products, 4) adiabatic flame sheath, and 5) surrounding charge gas. The apparent heat release rate predicted by the model is compared with data from a constant volume combustion vessel (CVCV) and two single-cylinder direct-injection diesel engines. The rate of charge air entrainment is determined from the correlation of a non-vaporizing, non-reacting jet with no wall impingement.

Four 1998 Mitsubishi Carismas, two equipped with direct injection and two with port fuel injection engines, were tested in 20,100 km intervals to determine the effect of mileage accumulation cycle, engine type, fuel and lubricant on vehicle deposits and emissions, acceleration and driveability performance. The program showed that engine fuel system deposits, including specifically those on intake valves, combustion chambers and injectors are formed in higher amounts in the GDI engine than the PFI engine. The fuel additive used reduced injector deposits and combustion chamber deposits in the GDI, but had no significant effect on intake valve deposits, which are affected by crankcase oil formulation. In GDI vehicles, deposited engines were found to have increased hydrocarbon and carbon monoxide emissions and poorer fuel economy and acceleration, but lower particulate emissions.

Exhaust NOx and particulate measurements were obtained at equivalent operating conditions in a direct-injection compression ignition engine for diesel and diethyl ether fuel. Particulate levels for diethyl ether were very low relative to the diesel fuel and did not increase significantly until the fuel to oxygen equivalence ratio was above 0.8. The log of fuel specific NOx for both the diesel and diethyl ether fuel were found to correlate well with the inverse of adiabatic flame temperature as has been observed by others in previous research. A newly defined heat release averaged, adiabatic flame temperature improved the correlation of both fuels. Differences in the correlations of the two fuels with this newly defined temperature were smaller than the scatter of the data.